background image

Honeywell International Inc.
400 Maple Grove Road
Ottawa, Ontario, K2V 1B8
Canada
CAGE: 38473
Telephone: 800-601-3099 (Toll Free U.S.A./Canada)
Telephone: 602-365-3099 (International Direct)
Website: 

www.myaerospace.com

Page T-1

Publication Number MN-0000042, Revision F

6 May 2011

Revised 28 Feb 2018

© Honeywell International Inc. Do not copy without express permission of Honeywell.

23-15-45

Legal Notice

 Export Control

These items are controlled by the U.S. government and authorized for export only to the country of ultimate 

destination for use by the ultimate consignee or end-user(s) herein identified. They may not be resold, transferred, or 

otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or 

end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval 

from the U.S. government or as otherwise authorized by U.S. law and regulations.

ECCN: 7E994.

ASPIRE-200

System Description, Installation, and Maintenance Manual

This guide provides procedures for installation, configuration, and operation of the equipment listed below.

Model

Part Number

Low Gain Antenna System

1541-K-1015-01

AMT-3500 Intermediate Gain Antenna System

1541-K-1007-01

AMT-700 High Gain Antenna System

1541-K-1006-01

AMT-3800 High Gain Antenna System

1541-K-1006-02

AMT-1800 Intermediate Gain Antenna System

1541-K-1007-42

AMT-1800 Intermediate Gain Antenna System with CCU-200

1541-K-1007-02

AMT-1800 Intermediate Gain Antenna System with CNX-250

1541-K-1007-32

AMT-3500 Intermediate Gain Antenna System with CNX-200

1541-K-1007-11 

AMT-1800 Intermediate Gain Antenna System with CNX-200

1541-K-1007-12 

Summary of Contents for ASPIRE-200











































































































































Reviews: