background image

N7635-1V2  12/07  Rev. A 

 

ADEMCO 5882AP 

RF RECEIVER 

INSTALLATION AND SETUP GUIDE

 

GENERAL INFORMATION 

The 5882AP RF receiver is designed for use with control 
panels that support an RF receiver connection 

via the 

remote keypad connection points

.  The receiver recognizes 

alarm, status and keypad control messages from wireless 
transmitters operating at 315 MHz.   

One or two individually identified receivers can be 
employed, depending on the control used. Connection of 
multiple receivers to a control can provide redundant 
coverage or extend coverage in large areas. 

Multiple 

receivers do not increase the number of transmitters that the 
system can support.

 See the control's instructions for specific 

information regarding the number and type of receivers that 
can be supported. 

These receivers feature a Spatial Diversity System which 
virtually eliminates the possibility of "Nulls" and "Dead 
Spots" within the coverage area. 

The 5882AP RF receiver is used in conjunction with 5800AP 
series transmitters. 

The number of zones that the 5882AP receiver can support 
depends on the control with which it is used. See the control 
panel’s instructions for specific details. 

If a receiver is connected to a system in which more than 
the permitted number of wireless zones have been 
programmed, a "SET UP ERROR" message (alpha keypads) 
or an "E4" or “E8" message (fixed-word keypads) will be 
displayed on the system's keypad, and none of the zones will 
be protected. 

The instruction manual that accompanies the control 
includes recommendations regarding receiver and 
transmitter locations, the types of wireless zones that can 
be programmed (e.g., ENTRY/EXIT, PERIMETER, 
INTERIOR, etc.), and the procedure for programming the 
receivers. 

These receivers should not be installed in an area subject to 
environmental extremes of below freezing (such as in a 
refrigerated area) or extremely high temperatures (such as 
an attic). 

INSTALLATION 

With some controls, a receiver may be mounted directly 
inside the control's cabinet (receiver circuit board only, 
without its plastic housing) instead of remotely (in its own 
housing). In both cases, avoid mounting the receiver 
antennas against a metal surface. 

1.

 

Remove the receiver's cover 

by inserting and 

twisting a screwdriver blade in the slot at the center of 
the cover's lower edge.

 

2.

 

If the receiver is to be mounted within the control's 
cabinet (refer to Figure 1):

 

a.

 

Remove the receiver's circuit board from its base by 
bending back the two flexible plastic tabs that hold 
the board's lower edge.  

 

b.

 

In the control's cabinet, unfasten and move the 
control circuit board downward (if already 
installed).  

 

c.

 

Hang two mounting clips (provided with the 
receiver) on the raised cabinet tabs, as shown in 
Detail B of Figure 1.  

 

d.

 

Insert the top of the receiver board between the 
rows of slots at the top of the cabinet, as shown in 
Detail A.  

 

e.

 

Position the base of the receiver board onto the 
mounting clips, and secure it to the cabinet with 
the supplied screws. See Detail B.  

 

f.

 

Hang two mounting clips (supplied with the control 
board), on the raised cabinet tabs as shown in 
Detail C in Figure 1.  

 

g.

 

Insert the top of the control board into the slots of 
the mounting clips secured in step e above.  

 

h.

 

Position the lower end of the control board into 
place on the mounting clips and secure both to the 
cabinet with the two supplied screws.  

 

i.

 

Insert both grounding lugs (supplied with the 
receiver) through the top of the cabinet into the left 
hand terminals of the antenna blocks (located on 
the upper edge of the receiver board), and secure 
them to the cabinet with the screws provided, as 
shown in Detail D.  

 

j.

 

Insert the receiver’s antennas through the top of 
the cabinet, into the block’s 

right-hand

 terminals, 

and tighten the screws.  

 

k.

 

Affix the receiver's Summary of Connections label 
to the inside of the control's cabinet door.  

 

l.

 

Discard the receiver's unused plastic cover and 
base.  

 

3.

 

If the receiver is to be located remotely from the 
control

 in its own plastic enclosure (not in a cabinet):

 

You will not need the circuit board mounting clips, 
grounding lugs, and screws included with the receiver. 

a.

 

If concealed wiring is to be used, route it through 
the rectangular opening at the rear of the base 
before mounting.  For surface wiring entry, a thin 
breakaway area is provided along the base's right 
edge.   

b.

 

Mount the receiver in the selected location. For 
greatest security, use all four mounting holes (two 
key slot holes and two round holes) provided in the 
plastic base.   

c.

 

Affix the receiver's Summary of Connections label 
to the inside of the housing cover.   

4.

 

Setting the DIP switches   

Set the receiver's DIP switch to identify the receiver's 
address (refer to the DIP switch chart in Figure 2).  

 

5.

 

Insert the wiring plug (with 4 flying leads) into 
the mating socket on the receiver 

(see Figure 2 for 

socket location). Connect the

 

4 wires to the control's 

corresponding remote keypad connection points (see 
“Interface Wiring” in the 

SPECIFICATIONS

 section).   

Summary of Contents for ADEMCO 5882AP

Page 1: ...e 1 a Remove the receiver s circuit board from its base by bending back the two flexible plastic tabs that hold the board s lower edge b In the control s cabinet unfasten and move the control circuit board downward if already installed c Hang two mounting clips provided with the receiver on the raised cabinet tabs as shown in Detail B of Figure 1 d Insert the top of the receiver board between the ...

Page 2: ...ut Aux Power GREEN Data Out to Control YELLOW Data In from Control BLACK Ground Range 60m nominal indoors from wireless transmitters the actual range to be determined with the security system in Figure 2 TO THE INSTALLER Regular maintenance and inspection at least annually by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system The insta...

Page 3: ...ng in bed violent explosions escaping gas improper storage of flammable materials overloaded electrical circuits children playing with matches or arson Depending on the nature of the fire and or location of the smoke detectors the detector even if it operates as anticipated may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Passive Infrared Motio...

Page 4: ...CLAIM THAT THE PRODUCT S FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT S WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any pre...

Reviews: