background image

___ __________________________ Honeywell 

Technical Support Inside

 Step by Step 

Created by Jim Venero            

 9/20/06 

 

 

7720P PROGRAMMING TOOL JUMPER SETTING 

FOR THE 7845GSM/IGSM

 
 

7720P programming tool’s manufactured before January of 1999 will not work on our new 
GSM communication module due to a jumper setting in the device. The symptom to expect is no 
power to the 7720P programming tool. The screen will be blank. There is no other symptom for 
this particular problem. The Internal jumper will have to be moved before the unit will work on 
a GSM radio. 
 
 

A new version 7720P programming tool (made after January 1999) would have the same 
symptoms as well if… 
 

You don’t have enough power to support both the GSM module and 7720P programming tool 

 

Make sure your GSM module has transformer (9VAC 15VA) and backup 
battery power (6V 3.1 AH). 

 

Faulty four pin cord 

 

Make sure your cord is plugged in all the way. 

 

Try unplugging your tool and plugging it back in. 

 

Leave your tool plugged in and try powering the GSM module down and then 
back up. 

 

Try reversing your programming cord. 

 
Maybe the internal software of the programming tool is bad 

 

If all of the above checks do not correct the problem your 7720P programming 
tool may have an internal problem and you will need to try a second tool at this 
point. 

 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 7720P









Reviews: