background image

®U.S. Registered Trademark
Copyright © 1997 Honeywell Inc.  •   All Rights Reserved

X-XX UL

INSTALLATION INSTRUCTIONS

208414, 208415 Replacement Power Supply

Kit for Electronic Air Cleaner

APPLICATION

These kits replace the power supplies with W8600E solid-
state performance indicators (SSPI) used in the F50F and
F58F  Electronic Air Cleaners. See Table 1.

NOTE:

The W8600E Remote Performance Indicator
driver circuit board has been calibrated with the
power supply in this kit. False wash indications
will occur if used with a different power supply.

69-1136-1

Table 1. Power Supply Replacement Guide.

NOTE:

Use the 120 Vac replacement power supply
indicated in Table 1 when servicing the F50F or
F58F electronic air cleaners which have been
modified with the 203365A transformer kit to
operate at 220/240 Vac.

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-
ous condition such as electrical shock.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for
your application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

WARNING

ELECTRIC SHOCK HAZARD. SAFETY HAZARD.
CAN CAUSE ELECTRICAL SHOCK OR
EQUIPMENT DAMAGE
Disconnect power before removing old power
supply board and installing replacement power
supply board.

To Remove Old Power Supply Board

NOTE:

It is advisable to observe the location of
leadwires to be replaced on the power supply.
Tag the leadwires as they are removed to help
you correctly reconnect them.

Open access door. See Fig. 1.

Open power box.

Nominal Size

Ionizer Current  

Replacement Power Supply  

(in.)

(mm)

(mA)

(OS No.)

F50F

120 Vac, 60 Hz

16 x 20

406 x 508

1.33

208414G

16 x 25

406 x 635

1.65

208414B

20 x 20

508 x 508

1.65

208414B

20 x 25

508 x 635

2.10

208414A

20 x 12-1/2

508 x 318

1.05

208414C

220/240 Vac,
50/60 Hz  

20 x 12-1/2

508 x 318

1.05

208415C

F58F

120 Vac, 60 Hz

20 x 25

508 x 635

2.10

208414A

Summary of Contents for 208414









Reviews: