background image

Packed in a temporarily assembled condition

Hitachi Plasma Display Ceiling Mount Unit

Model

CMPAT04

Installation Instructions

Thank you for purchasing the Hitachi Plasma Display Ceiling Mount Unit.
To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual
in a safe place for future reference.

This plasma display ceiling mount unit is for use only with the following models : CMP401X, CMP402HD, CMP307X

♦  

Special techniques are necessary for installation of
the plasma display.

Do not attempt to perform this work by yourself.

♦  

Request an installation specialist to install this unit.

♦  

This company assumes absolutely no responsibility
for injuries and damages that may occur due to
improper installation and handling.

To dealers and shops

To ensure customer safety, be sure to design the
installation location so that the strength is sufficient
to withstand the weight of both the plasma display
and the Ceiling mount unit.

Always use at least two persons for all
installations.

Firmly install coupling pins, snap pins and screws
as specified in the installation instructions.

Parts Configuration Chart

In the parts packing

Parts for CMP401X only

Coupling pin

X

2

Usage cautions to ensure correct usage

• 

The following symbols are used to ensure safe usage of the product, to prevent danger to

yourself and other parties and to prevent damage to property.

Symbols

This symbol indicates that incorrect handling due to ignoring this symbol
can result in the possibility of personal injury or even death.

This symbol indicates
additional cautions
(including warnings).

This symbol indicates that incorrect handling due to ignoring this symbol
can result in the possibility of personal injury and physical damage.

This symbol indicates
forbidden actions.

This symbol indicates
required actions.

Ceiling mount unit

X

1

Snap pin

X

2

Angle

adjustment unit

X

1

(left)                        (right)

Display mount fitting

1 each left/right

M6 

X

18 screw

X

8

Support

X

2

M4 x 12 screw

X

4

WARNING

CAUTION

Caution

(general)

Forbidden

(general)

Required

(general)

Disassembly

prohibited

Indicates that the power

plug is to be disconnected

from the power outlet.

Summary of Contents for CMPAT04











Reviews: