GE 1400 Series User Manual Download

Page: 1 / 24

Questions? Call GE Answer Center at 800.626.2000

Visit our Website at:

www.GEAppliances.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS

Installation

Over the Range

Instructions

Microwave Oven

Read these instructions completely and carefully.

•

IMPORTANT –

Save these

instructions for local inspector’s use.

•

IMPORTANT –

Observe all

governing codes and ordinances.

•

Note to Installer –

Be sure to leave these

instructions with the Consumer.

BEFORE YOU BEGIN

•

Note to Consumer –

Keep these

instructions for future reference.

•

Skill level

– Installation of this appliance requires

basic mechanical and electrical skills.

•

Proper installation is the responsibility of the installer.

•

Product failure due to improper installation is not

covered under the Warranty.

For a Spanish version of this manual, visit our Website at www.GEAppliances.com.
Para consultar una version en español de este manual de instrucciones, visite nuestro sitio
de internet www.GEAppliances.com.

Summary of Contents for 1400 Series

























Search results

Summary of Contents for 1400 Series

Reviews:

Related manuals for 1400 Series

Brands by name

Popular brands

GE 1400 Series, Installation Instructions Manual

Search results

Summary of Contents for 1400 Series

Reviews:

Related manuals for 1400 Series

Brands by name

Popular brands