background image

www.Fisher.com

Fisher

 D3 Control Valve with easy-Drive

 Electric

Actuator

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Educational Services

3

. . . . . . . . . . . . . . . . . . . . . . . . .

Installation

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Instructions for “Safe Use” and Installations

in Hazardous Locations

4

. . . . . . . . . . . . . . . . . . . . .

Startup Overview

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Important Technical Notice for easy-Drive

Electric Actuator

8

. . . . . . . . . . . . . . . . . . . . . . . . . .

Default Input Signals

9

. . . . . . . . . . . . . . . . . . . . . . . . .

Configuration

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input Configuration

9

. . . . . . . . . . . . . . . . . . . . . .

Changing the Inputs from Default Settings

9

. . .

Modbus Setup

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Calibration Instructions

11

. . . . . . . . . . . . . . . . . .

Setting the Valve Flow Adjuster

15

. . . . . . . . . . . . . . . .

Troubleshooting

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Valve Plug and Seat Ring Maintenance

18

. . . . . . . . .

Packing Maintenance

20

. . . . . . . . . . . . . . . . . . . . . . . .

Parts Ordering

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Kits

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Appendix A - Modbus

25

. . . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Fisher D3 Control Valve with easy-Drive
Electric Actuator

W9795-4

Introduction

Scope of Manual

This instruction manual provides installation, maintenance, and parts information for the Fisher D3 control valve with
easy-Drive electric actuator.

Do not install, operate, or maintain a D3 valve with easy-Drive electric actuator without being fully trained and
qualified in valve, actuator, and accessory installation, operation, and maintenance. 

To avoid personal injury or

property damage, it is important to carefully read, understand, and follow all the contents of this manual, including all
safety cautions and warnings. 

If you have any questions about these instructions, contact your 

Emerson sales office

 or

Local Business Partner before proceeding.

Instruction Manual

D103460X012

D3 Valve with easy-Drive Actuator

October 2017

Summary of Contents for Fisher D3





































Reviews:

Related manuals for Fisher D3