Emerson ASCO 185 Series User Manual Download

Page: 1 / 12

381333–319 D

50 Hanover Road, Florham Park, New Jersey 07932–1591 USA

For sales or service call 1 800 800–2726 (ASCO) www.ascopower.com

ASCO POWER TECHNOLOGIES CANADA PO Box 1238, 17 Airport Road, Brantford, Ontario, Canada N3T 5T3

Operator’s

Manual

Series 185

Automatic Transfer Switches

100 through 400 ampere sizes

DANGER is used in this manual to warn of high

voltages capable of causing shock, burns, or death.

WARNING is used in this manual to warn

of possible personal injury.

CAUTION is used in this manual to warn

of possible equipment damage.

An experienced licensed electrician must install the ATS.

100–230 ampere sizes

Refer to the outline and wiring drawings provided with

your ASCO Series 185 ATS for all installation details.

ASCO Series 185 Automatic Transfer Switches (ATSs) are

Listed under Underwriter’s Laboratories Standard for

Transfer Switch Equipment, UL–1008. They are intended

for use only in optional standby systems in accordance with

the National Electrical Code, NEC/NFPA 70, Article 702.

This ATS is for use with 2–wire automatic–start generators

only.
Refer to Application Information 381339–292 to confirm

that you have selected the appropriate product for the

intended installation.
This automatic transfer switch is intended for standby

power applications in residential / light commercial use

only.

This product is not intended for emergency
or life–support systems.

If you have more stringent application requirements contact

ASCO Power Technologies for other products suitable for

critical applications.

Rating Label

Each automatic transfer switch contains a rating label to

define the loads and fault circuit withstand / closing ratings.

Refer to the label on the transfer switch for specific values.

Do not exceed the values on the rating label.

Exceeding the rating can cause personal

injury or serious equipment damage.

TABLE OF CONTENTS

page

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . .

CONTROLLER

2–5

. . . . . . . . . . . . . . . . . . . . . . . .

FUNCTIONAL TEST

. . . . . . . . . . . . . . . . . . . . . .

SEQUENCE OF OPERATION

. . . . . . . . . . . . .

TROUBLESHOOTING

8–9

. . . . . . . . . . . . . . . . . .

INDEX

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Summary of Contents for ASCO 185 Series













Search results

Summary of Contents for ASCO 185 Series

Reviews:

Related manuals for ASCO 185 Series

Brands by name

Popular brands

Emerson ASCO 185 Series, Operator'S Manual

Search results

Summary of Contents for ASCO 185 Series

Reviews:

Related manuals for ASCO 185 Series

Brands by name

Popular brands