background image

About this Manual

This manual is designed to assist users in installing, configuring and
troubleshooting the AcerISDN P10 ISDN card.  Information in this
document has been carefully checked for accuracy; however, no guarantee
is given as to the correctness of the contents.  The information contained in
this document is subject to change without notice.

Copyright

© Copyright 1997-1998, Acer Netxus Inc. All Rights Reserved.

This document contains proprietary information protected by copyright.  All
rights are reserved.  No part of this manual may be reproduced by any
mechanical, electronic, or other means, in any form, without the prior
written permission of the manufacturer.

Trademarks

All trademarks and registered trademarks are the property of their respective
owners.

CE Approval

All CE approved ISDN devices may be connected to the Euro-
ISDN in all countries of the EU.

D129626H

D129627H

The 

AcerISDN P10

 has been approved by the German BZT

according to the new European procedure and may therefore be
connected to the Euro-ISDN in all EU countries.  This ISDN card
therefore complies with:

NET 3 (ISDN Basic Rate Access)

Electromagnetic Compatibility Standards

Safety Standards

Summary of Contents for ISDN P10






































Reviews: